Removing ingrained dirt from Crushed Edge Limestone tiles in Corby

Limestone is a natural stone with a lot of unique character and surface features with each tile being uniquely different from the last. These surface characteristics however can however make a stone very difficult to clean and unless sealed can result in dirt becoming trapped and ingrained. These particular Limestone tiles installed throughout the downstairs floor of a house in Corby are known as Crushed Edge Limestone and have an increased susceptibility to this issue. As you can see from the photographs below the crevices in the tile have become black with trapped dirt which has proved very difficult to clean.

Crushed Edge Limestone Corby Before Crushed Edge Limestone Corby Before

Cleaning Crushed Edge Limestone

Limestone is a very hard surface that has to be burnished with diamond encrusted pads to restore the finish so we set about this task using a set of Tile Doctor Burnishing Pads. Before starting however we soaked the floor in Tile Doctor Pro-Clean and scrubbed this into the tile surface spending particular attention on the grout lines; this process gets a head start on the cleaning and also remove any grit etc. that might cause problems before burnishing. The soiled solution was then rinsed away using water and all was removed using a wet vacuum.

Burnishing Crushed Edge Limestone

The burnishing pads come in a set of four, you start with the coarse pad together with a little water and this cut’s through and removes surface grime and any remaining surface sealer. The resultant slurry is washed away and you then progress through the other finer pads one by one until you get to the final polishing pad which provides a nice shine. You need to rinse the tiles in-between and use a wet vacuum to remove the slurry.

Sealing Crushed Edge Limestone

When we came back the next day we tested a few areas for dampness before starting to seal the floor, this is an important step for this type of tile as it can easily trap dirt. We chose Tile Doctor Ultra-Seal for this, it’s a natural look impregnating sealer that occupies the tiny pores in the stone preventing dirt and other contaminates from becoming ingrained, two coats were sufficient. Once the sealer had fully dried we went over it with a white buffing pad to finish.

Crushed Edge Limestone Corby After Crushed Edge Limestone Corby After

 
 

Cleaning Limestone Tiles in Northamptonshire

Ceramic Tiled Bathroom Refreshed in Kettering

This was a straight forward request to rejuvenate the ceramic tile and grout around the bath at a house in the town Kettering. The glazed ceramic tiles where in good condition but the grout and seal around the bath had become quite grubby and stained with dyes from shampoos, soaps and had gone dark in some areas where mould had started to get a foothold.

Ceramic Bathroom Tiles Before Cleaning Kettering Ceramic Bathroom Tiles Before Cleaning Kettering

Cleaning Ceramic Tile and Grout

We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning showers. The spray delivery is important as mixing the cleaning product with air makes it lighter and helps it cling to the tile and grout. The Oxy-Pro was left to soak in for around 15 minutes before being scrubbed into the tile and grout using a stiff grout brush. This action cleaned up the grout and tile nicely removing stains from shampoos and soaps etc.

Removing Mould from Grout

The grout was looking much improved but there was however some evidence of mould remaining which needed dealing with. To tackle this we used Tile Doctor Mould Away which is designed to remove mould off Silicone and Grout. It’s very easy to use, you simply spray the Silicone or Grout to be treated with Mould Away then leave to soak in for twenty minutes and then scrub with a brush and rinse with water repeating the process until the mould has disappeared, in extreme cases you can leave it for a few hours but we didn’t need to do that.

Ceramic Bathroom Tiles After Cleaning Kettering Ceramic Bathroom Tiles After Cleaning Kettering

I was unable to use any tools on this job so it took a fair amount of manual effort but the results were well worth it as you can see.
 
 

Refreshing a Ceramic Tiled Bath in Kettering

Cleaning Patios and Paths in a Titchmarsh Garden

These photographs are from the garden of a house in the beautiful village of Titchmarsh in Northamptonshire. The request was to clean the patios and paths which if not cleaned regularly become dirty and lose their appearance during the English winter.

Stone Circle Before Cleaning Gazebo Before Cleaning

Cleaning Patios and Paths

The process I follow for cleaning path’s, patios and paving in general is basically to apply a strong dilution of Tile Doctor Pro-Clean and then let it soak in to get to work on the dirt and grime for ten minutes before scrubbing with a stiff brush; this is then followed by pressure washing.

Stone Circle During Cleaning Stone Circle During Cleaning

Home owners can buy pressure washing machines and many domestic models are available in DIY stores however none are as powerful as the machines used by Tile Doctors which can generates pressures far in excess of a domestic system that make light work of cutting through grime.

Stone Circle After Cleaning Gazebo After Cleaning

 
 

Patio Cleaning in Northamptonshire

Cleaning and Sealing Kitchen Slate Tiles in Corby

Another example of a tired Slate Tiled floor that was in need of a clean and seal, this time in the industrial town of Corby famous for its iron and steel works.

Slate floor before cleaning Corby Slate floor before cleaning Corby

Cleaning Slate Kitchen Tiles

To get the Slate tile and grout clean the a dilution of Tile Doctor Pro-Clean was applied which was left to soak into the tile for ten minutes before scrubbing it in with a rotary machine fitted with a black scrubbing pad and then using a stiff grout brush to clean along the grout lines.

Slate floor during cleaning Corby Slate floor during cleaning Corby

The floor was then thoroughly rinsed using clean water which was then removed using a wet vacuum; there were a few stubborn areas that needed further attention which were re-treated. The last step of the cleaning process was to use a high pressure cleaning tool that extracts as well as washes, we normally use this tool for cleaning carpets but it also does a great job of giving a hard floor a thorough rinse to remove any trace of cleaning product before sealing.

Slate floor during cleaning Corby Slate floor during cleaning Corby

Sealing the Slate Tiled Floor

The floor was left to dry and we came back the next day to seal the slate using five coats of Tile Doctor Seal and Go applied using a paint pad applicator. I usually use Seal and Go for slate tiles as it provides good stain protection with adds a nice sheen finish that adds to the look of the floor.

Slate floor during sealing Corby

The job took two days and the floor now looks transformed.

Slate floor after sealing Corby Slate floor after sealing Corby

 
 

Cleaning and Sealing a Slate Tiled Floor in Northamptonshire

Cleaning and Sealing Kitchen Slate Tiles in Towcester

These photographs of a Slate tiled floor were taken in the Kitchen of a house in Towcester where the slate was looking rather dull and had lost its appeal. This does happen with natural stone floor where the sealer which can add a shine to the stone becomes worn down and ineffective.

Towcester Slate Tiles Before Cleaning Slate Tiles Towcester Before Cleaning

Cleaning Chinese Slate Tiles

We removed the kickboards from the kitchen units and lined the skirting boards with green Frog tape in order to protect them from cleaning fluids. The next step was to soak the floor in a dilution of Tile Doctor Pro-Clean which we let soak into the tile for 10-15 minutes before scrubbing it in with a rotary machine fitted with a black pad and then using a stiff grout brush to clean out the grout lines.

Slate Tiles Towcester Scrubbing Slate Tiles Towcester Scrubbing

The floor was then thoroughly rinsed using clean water which was then removed using a wet vacuum. The floor was now free of sealers etc. and this showed up a few stubborn areas that needed to be retreated and washed down again. It’s important to give the floor a good rinse to ensure it’s free of any cleaning products as they can upset the sealer.

Slate Tiles Towcester After Cleaning Towcester Slate Tiles After Cleaning

Sealing the Slate Tiled Floor

The floor was left to dry and we came back the next day to seal the slate using five coats of Tile Doctor Seal and Go applied using a paint pad applicator. I usually use Seal and Go for slate tiles as it provides good stain protection with adds a nice sheen finish that adds to the look of the floor.

Slate Tiles Towcester After Sealing Slate Tiles Towcester After Sealing

The job took two days and the floor now looks much better and much easier to clean, certainly the customer was very pleased and left the following message on our feedback system.

Phil is extremely professional and provided excellent customer service. He explained the process in detail and did a thorough job and worked extremely hard. The job was completed in the time proposed with a brilliant result. We have no hesitation in recommending Phil to others. Thank you.
Pete and Angie, Towcester
 
 

Cleaning and Sealing a Slate Tiled Floor in Northamptonshire

Power Washing Paving Slabs in Great Oakley

This was a straight forward request to Power Wash Paving Slabs outside a house in Great Oakley. I wouldn’t normally add this to my blog however it occurred to me that a lot of my customers don’t realise Tile Doctor’s have invested in high pressure equipment that can be used externally as well as internally. In the photograph below you will see a picture of our van which contains a very high pressure truck mounted cleaning system which can generates pressures far in excess of a domestic system.

Tile Doctor Northamptonshire Truck Mounted Pressure Cleaning

Cleaning Paving Slabs

You can see from the photographs below that we were able to cut through the soil and grime built up on the surface of the tiles without too much trouble, fortunately these were large slabs as you do have to be careful around the joints where too much power can dislodge the mortar in-between the slabs. Also working outside does have the added advantage that there is a lot less preparation to do to protect other surfaces. It wasn’t necessary in this case but if you do struggle to clean paving slabs yourself you should apply a strong dilution of Tile Doctor Pro-Clean first and then let it soak in before scrubbing it in with a stiff brush, brick acid cleaners that you can buy in the DIY stores are very strong and you have to be very careful with them where as Pro-Clean is an alkaline product.

Cleaning Paving Slabs in Great Oakley Cleaning Paving Slabs in Great Oakley

 
 

Patio Cleaning in Northamptonshire

Kitchen Quarry Tile Cleaning and Sealing in Rushden

This job was to strip and re-seal these Quarry tiles installed in a commercial kitchen which was undergoing refurbishment at a canteen in Rushden, Northamptonshire. The tile finish had dulled and there was a lot of staining to the grout.

Quarry Tiles in Rushden before cleaning

Cleaning Quarry Tiles

As there was little in the way of kitchen units to protect I go straight down to stripping down the floor using a strong dilution of Tile Doctor Pro-Clean which is a multi-purpose cleaner/stripper that’s safe to use on stone, tile and grout. The solution was applied with a mop and left it to dwell on the floor for twenty minutes in order to give it chance to soak into the tile surface and get to work on the existing sealer and dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad and stiff hand brushes were used along the grout lines to get the grout clean. The resulting soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and stubborn areas re-treated. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.

Sealing Quarry Tiles

After checking the tiles had dried I proceeded to seal the floor using four coats of Tile Doctor Seal and Go which will protect the floor from staining going forward and also adds a nice shine to the tile.

Quarry Tiles in Rushden After cleaning

 
 

Commercial Kitchen Quarry Tile cleaning in Northamptonshire

Polished Marble Floor Covered in Grout Haze in Irthlingborough

These photos are from a newly installed Polished Marble floor in the kitchen at a residence in Irthlingborough Northants which had been left covered in grout haze. The customer called the builder back as they were unhappy with the finish but he could not rectify the problem, so the customer contacted Tile Doctor to see if anything could be done.

This is a problem we often come up against where a builder or tiler does a good job of laying the tiles but for some reason doesn’t remove all the grout from the tile and we have even seen some jobs where the grout smears have been sealed over which makes it even more noticeable especially on a polished floor. Fortunately for the customer we are able to resolve such problems and after agreeing the process we set about solving the problem.

Marble Tiled Floor In Irthlingborough before cleaning

Burnishing Polished Marble Tiles

To protect the kitchen units from any splashing etc. all the kick boards were removed and plastic sheeting fitted to protect new doors and panels before any work was undertaken.

Polished Marble is a very hard surface that has to be burnished with diamond encrusted pads to restore the finish so we set about this task using a set of Tile Doctor Burnishing Pads. The pads come in a set of four, you start with the coarse pad together with a little water and this cut’s through and removes surface grime, surface seal and in this case grout haze as well. You then progress through the other finer pads one by one until you get to the final polishing pad which provides a high polish. The pads did the trick and had the surface polished to a high shine which was the look the customer was hoping they would have had in the first place.

The floor was looking great but I was concerned about the grout, most people don’t realise but the top layer of grout is actually slightly porous and will attract dirt and discolour over time, this is especially the case in a bathroom or kitchen. After discussing this with the customer we sealed the grout with Tile Doctor Ultra-Seal which provides a natural look whilst preventing contaminates reaching the grout.

All in the job took two days and the customer was extremely happy with the final result.

Marble Tiled Floor In Irthlingborough after cleaning

 
 

Cleaning and Polishing Marble Tiled floor in Northamptonshire

Restoring a Victorian Tiled Hallway in Kettering

The following photos are from a Victorian tiled hallway floor at a residence in Kettering Northants which had been covered with carpet for the last thirty odd years; to make matters worse the carpet had been stuck down with adhesive which was proving very difficult to remove.

The customer phoned to see if it would be possible to restore the floor back to its former glory as it was very dirty and the colours were dull not to mention the glue. After a home visit and testing a small area to prove we could do the work, the customer booked us in to carry out the service before completing the decorating of the hallway. It’s always a good idea to have any heavy restoration work done before you decorate as heavy machinery is used and it can be a messy job.

Victorian floor in Kettering before cleaning 1 Victorian floor in Kettering before cleaning 2

Cleaning Victorian Tiles

To remove the glue and restore the tiles Tile Doctor Remove and Go was left to soak into the tile before being brushed in with a rotary machine fitted with a black scrubbing pad. This process also works to lift out the embedded dirt from the floor tile; once done the soiled solution was removed using a wet vacuum and the floor rinsed with clean water to remove the product from the tile.

To get the grout clean Tile Doctor Grout Clean-up was sprayed onto all the grout lines and then hand scrubbed in with stiff brushes; this was then followed by a second wash and rinse.

The hallway was still in general use so the floors were then sheeted up for three days to protect them whilst the floor tiles and grout were allowed to dry out assisted by a dehumidifier which we left on site.

Sealing Victorian Tiles

On our return we remove the sheeting and damp tested the tiles to make sure they had dried sufficiently; all was well so we sealed the floor by applying five coats of Tile Doctor High Shine as the customer had requested a high gloss finish in order to fully bring out the colours of the tiles.

Victorian floor in Kettering after cleaning 1 Victorian floor in Kettering after cleaning 2

I think you will agree from the photographs we have managed to achieve this, certainly the customer was very happy with the results.
 
 

Victorian Tile Restoration in Kettering, Northamptonshire

Kitchen Quarry Tile Cleaning and Sealing in Daventry

Apologies for the poor quality of these grainy Quarry Tile Cleaning photographs taken in the kitchen of a residential property in Daventry but it was the middle of winter and I was using my phone camera which doesn’t have an effective flash. Hopefully you can see from the photograph below how dirt had become ingrained into the tile and stains to the grout.

Quarry Tiled Kitchen Floor Before Cleaning

Cleaning Quarry Tiles

To get the floor clean I removed the kick boards around the base of the kitchen units and applied a dilution of Tile Doctor Pro-Clean mixed with NanoTech Ultraclean which adds tiny abrasive particles to an already powerful alkaline cleaning product that is safe to use on tile and stone. It was applied with a mop and left it to dwell on the floor for twenty minutes first in order to give it chance to soak into the tile and get to work on the dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad, stiff hand brushes were along the grout lines. The soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and allow us to see which areas need further attention. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.

Quarry Tiled Kitchen Floor During Cleaning

Sealing Quarry Tiles

On my return the floor was checked in a number of places with a damp meter to confirm it had dried which it had and it was then sealed using numerous coats of Tile Doctor Seal and Go which adds a nice shine to the floor as well as providing a surface seal that will help protect the tile from stains going forward. Sealing can take some time as you need to let the first coat dry before starting the second.

Quarry Tiled Kitchen Floor After Cleaning and Sealing

 
 

Quarry Tile Maintenance in a Daventry Kitchen

Cleaning and Sealing Black Welsh Slate Floor in Whilton

The photographs below are taken from a job in the village of Whilton near Daventry where we were asked to clean and seal a black Welsh Slate tiled floor that was installed in a Kitchen and adjacent dining area.

The customer was concerned that the floor was very dull and proving difficult to keep clean additionally she was having a new kitchen fitted and didn’t want to replace the floor but wanted to achieve a shiny finish that was easy to maintain.

Welsh Black Rough Slate kitchen Before Cleaning 1

On the initial survey I found the sealant was of a poor quality and had all but worn off allowing stain and soil to seep into the grout and stain the tiles, stains which were difficult to remove with normal household cleaning products.

Cleaning Welsh Slate Tiles

After fully masking up the areas to protect the skirting boards and wooden steps I carried out a deep clean with a dilution of Tile Doctor Remove and Go worked in with a rotary machine fitted with a black scrubbing pad in order to strip the floor and remove the old wax sealer and tackle the ingrained stains and grime. Additionally the grout lines were scrubbed using stiff hand brushes to bring them back to an acceptable appearance. The soiled cleaning solution was removed using a wet vacuum and then washed down with clean water so we could see the areas that needed further work and repeated the process.

Once I was happy with the overall appearance the entire area was given a thorough rinse and wash to remove any chemical and neutralise the floor before sealing. We left a dehumidifier in place to assist in the drying process as we wanted to ensure the tile and grout was fully dry prior to application of a sealer.

Welsh Black Rough Slate kitchen after Stripping

Sealing the Slate Tiled Floor

We came back two days later and checked the floor was dry which it was so we proceeded to apply the sealer for which we chose Tile Doctor Seal and Go which is a water based sealer (no smell) that is recommended for Slate tiles and provides good stain protection with a low sheen finish that really does bring the floor alive. It took five coats before the slate tiles were fully sealed.

Welsh Black Rough Slate kitchen After Cleaning and Sealing 1 Welsh Black Rough Slate kitchen After Cleaning and Sealing 2

 
 

Cleaning and Sealing a Welsh Slate Tiled Floor in Wilton Village near Daventry

Restoring a Victorian Tiled Hallway in Towcester

The photograph below is from a Victorian tiled hallway floor that we were asked to restore in the historic town of Towcester, Northamptonshire; the owner wanted the tiles restored as an original feature. You can see from the photograph below how dull and neglected the tiles were so we had our work cut out.

Victorian Tiles in Towcester Before Restoration

Cleaning Victorian Tiles

We set about cleaning the tile using Tile Doctor Pro-Clean which is a powerful alkaline cleaning product that is safe to use on tile and stone. It was applied with a mop and left it to dwell on the floor for ten minutes first in order to give it chance to soak into the tile and get to work on the dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad, stiff hand brushes were used in difficult to get to places and along the grout lines requiring a substantial amount of elbow grease. The soiled water was picked up with a wet and dry vacuum and the floor was rinsed with clean water so we could see the result.

Unfortunately there were a number of stubborn areas and a stronger product was needed to shift them so we applied a dilution of Tile Doctor Remove and Go which is a coating remover that can shift most issues, again this was applied and left to dwell for a while before working it into the stubborn stains using hand brushes. The dirty solution was removed again using the wet and dry vacuum and we could see the tiles were now clean so the floor was given a thorough rinse several times with fresh water to remove any leftover chemical and then left to dry overnight.

Sealing Victorian Tiles

The next day the floor had dried so we were able to seal it using four coats of Tile Doctor Seal and Go which adds a nice shine to the floor as well as providing a surface seal that will help protect the tile from stains going forward.

Victorian Tiles in Towcester After Restoration

A lot of effort but what a transformation and well worth the work that went into it as you can see from the photograph above.
 
 

Victorian Tile Restoration in Brighton

Cleaning and Sealing Chinese Slate Floor in Kingsthorpe

On this page you will find a good selection of photographs taken during the cleaning and sealing of a Chinese Slate tiled floor in the village of Kingsthorpe, Northampton. The floor had been installed in the kitchen and the lounge and both the slate and the grout was in need of a deep clean.

Chinese Slate Tile Before Kitchen

Cleaning Chinese Slate Tiles

The first thing we do is to protect anything that can’t by moved by wrapping it in a plastic sheet once this was done we set about scrubbing the slate tiled floor with Tile Doctor Pro-Clean and a rotary machine fitted with a black pad, we used a grout brush to clean out the grout lines and then rinsed the floor thoroughly with clean water.

Chinese Slate Tile Cleaning Kitchen Chinese Slate Tile Cleaning Lounge

It’s not until the floor has been washed down that you can spot any stubborn or missed areas so it’s not usual to have to repeat this process until a satisfactory result is obtained. We had both the kitchen and lounge to do and this took most of the day, before leaving for the evening we switched on an air blower to help the floor to dry.

Chinese Slate Tile Lounge Drying

Sealing the Slate Tiled Floor

We came back the next day and checked the floor was dry, fortunately the air blower had done its job and we were able to get on with the sealing the floor.

To seal the floor five coats of Tile Doctor Seal and Go were applied using a paint pad applicator. Seal and Go is recommended for Slate tiles and provides good stain protection with a low sheen finish that really does bring the floor alive.

Chinese Slate Tile Sealing Lounge Chinese Slate Tile Lounge After

 
 

Cleaning and Sealing a Slate Tiled Floor in Northamptonshire

Travertine Kitchen floor Cleaned and Sealed in Brixworth

This house in Brixworth near Northampton had Travertine tiles fitted in the kitchen and Ceramic tiles in the hallway, both of which were in need of a deep clean. It was clear that the sealer on the Travertine tiles had stopped working allowing dirt to become ingrained in the surface causing it to become very difficult to clean, you can see this quite clearly in the photographs below, the grout had also become darker.

Travertine Kitchen Tiles Before Travertine Kitchen Tiles Before

Cleaning Travertine Tile

Travertine is a very hard surface so normally it’s necessary to use diamond encrusted burnishing pad system to clean, strip and polish the floor, in this case however I decided to try a combination of stripping and high pressure clean instead. I started by applying a dilution of Tile Doctor Pro-Clean which is a multi-purpose tile cleaner safe to use on natural stone. This was left to dwell on the floor so it could get to work on the dirt before being worked in to the stone using a black stripping pad fitted to a rotary machine. This was then rinsed off with high pressure spinning tool operating at 1200 PSI to blast out the dirt from the pitted tiles and badly soiled grout lines.

Sealing Travertine Tile

The tiles were left to dry overnight and we came back the next day to seal the Travertine tile with two coats of Tile Doctor Seal and Go which will provide on-going stain protection as well as giving the tiles the glossy finish the customer had requested.

Travertine Kitchen Tiles After Travertine Kitchen Tiles After

Cleaning Ceramic Tile

To tackle the Ceramic tiles in the hallway we used a similar system involving the use of Tile Doctor Pro-Clean and a scrubbing pad to get the tiles clean; Ceramic tiles however are usually glazed and won’t take a sealer the top layer of Grout however is porous and to protect that we applied Tile Doctor Seal and Go along the grout lines.

Ceramic Tiled Hallway Before Ceramic Tiled Hallway After

 
 

Travertine and Cermaic Tiles maintenance in Northampton

Cleaning and Sealing a dirty Sandstone Tiled Floor in Hannington

This customer in Hannington had a badly soiled and stained rough sandstone tiled floor which they were finding extremely difficult to keep clean. It was apparent that the previous sealer was no longer working well and so the only solution was to strip and clean the floor then re-seal.

Sandstone Hannington Before Cleaning

Cleaning a Rough Sandstone Tiled Floor

I stripped the floor using a strong dilution of Tile Doctor Pro-Clean combined 50/50 with NanoTech UltraClean to produce a strong stripper and cleaning solution that is safe to use on natural stone. This was worked into the tile using a rotary machine fitted with a scrubbing brush rather than a pad to cope better with the uneven finish of the rough Sandstone.

This activity was then followed with a high pressure spinning tool operating at (1200psi) in four to five metre square sections. The spinner tool washes the tile surface with high pressure water and also extracts the water from the surface simultaneously which dislodges and loosens built up ingrained grim from the tiles and grout.

The floor was now clean and free of old sealer and was left to dry for a couple of day aided by turbo fans and dehumidifiers which we left at the property.

Sandstone Hannington After Cleaning Sandstone Hannington After Cleaning

Sealing a Rough Sandstone Tiled Floor

When we came back we first tested the floor with a damp meter in a few different locations to make sure no dampness remained in the stone, fortunately the machines we had left behind had done their job and the floor was completely dry so we started to seal the floor. For this the customer had chosen Tile Doctor Seal and Go which adds a high gloss finish as well as lifting the natural colour in the stone.

Sandstone Hannington After Sealing Sandstone Hannington After Sealing

 
 

Sandstone Floor Cleaned and Sealed in Northamptonshire

150 Year Old Quarry Tile Restoration in Northants School

Shown below are some photographs for a job we did recently restoring 150 year old Quarry Tiles at a School near Peterborough in Northamptonshire. The school had a lot of problems with this floor over the years and had called in another cleaning company several months prior but found that within weeks the sealant they had applied had started to bubble and peal off. The floor was suffering from ongoing dampness problems in some areas, which isn’t unusual for a floor in an old building as damp proofing is a relatively modern concept. Tile Doctor was called in to try to rectify the issues.

Quarry Tiles Failed Sealer Quarry Tiles Failed Sealer

Cleaning Quarry Tiles

The work was booked to be carried out before Xmas and we spent hours stripping the tiles with Tile Doctor Pro-Clean agitated with a buffing machine fitted with a black scrubbing pad with little affect. To resolve the problem we resorted to getting down on hands and knees with a steamer and scrapper and spend the next 3 days taking off several coats of sealant and wax stripping quarry tile floor. The floors were then allowed to dry for ten days over Christmas.

Sealing Quarry Tiles

We returned in the New Year and took damp meter readings from the floor to ensure it was dry before sealing. The choice of sealer was vital given the floor was 150 years old and it was essential we chose one that was breathable to ensure any dampness could permeate up through the floor and not get trapped causing a problem. We settled for Tile Doctor Colour Grow which is breathable and offers good stain protection as well as enhancing the colour in the tile, two coats were sufficient to ensure to seal the floor. The last step was to buff the floor with a rotary machine fitted with a white pad to bring out the shine.

Quarry Tiles Cleaned Applying Sealer Quarry Tiles Cleaned Applying Sealer

Quarry Tile Maintenance

The school had faced problems maintaining this floor in the past so I returned to site the following week to explain the best method for cleaning the floor going forward; this essentially involves using two buckets, once containing cleaning solution and another to rinse out the mop, I also gave them a complimentary bottle of Tile Doctor Neutral cleaner and a white buffing pad to point them in the right direction. Neutral Cleaner is a PH Neutral formula which unlike most acid products will not degrade the sealer over time.

Quarry Tiles Cleaned and Sealed Quarry Tiles Cleaned and Sealed

 

Northants School Quarry Tiled floor restoration

Dull and Stained Semi Riven Black Slate Floor Tiles in Kettering

Great testimonial here from the customer who described her floor as “bleak drab grey dull slate with heavily stained brown looking grout”. The slate tiles are Semi Riven Black Slate laid on the floor of a Kitchen in a house in Kettering.

Cleaning the Slate Floor Tiles

We used a solution of Tile Doctor Pro-Clean and mixed with warm water scrubbed into the floor to release the dirt. A stronger dilution of Pro-Clean was required in some areas with stubborn stains. The slate floor tiles were then rinsed with water using a wet vacuum to soak up the excess; we then rinsed and vacuumed the floor a second time to make sure there was no Pro-Clean residue left behind. The floor was then covered with a dust sheet and left to dry overnight.

Semi Riven Black Slate floor scrubbing Semi Riven Black Slate floor scrubbing
Semi Riven black slate floor grout scrubbing

Sealing the Slate Floor Tiles

The next day I used a damp tester it to make sure the slate floor was fully dry and then proceeded to apply several coats of Tile Doctor High Shine sealer which gives a nice deep shine as well as providing stain protection. I mentioned to the customer about the free bottle of Ph Neutral Tile and Stone Cleaner that Tile Doctor send out on completion of customer feedback to ensure she had the right product to clean her newly sealed slate tiles going forward. A lot of people don’t realise that many products available for tile cleaning in supermarkets are really designed for ceramic floors and that they can erode the sealers due to their high ph content.

Semi Riven Black Slate floor cleaned sealed Semi Riven Black Slate floor cleaned sealed

My customer Ms Hayes was very pleased with the results and left the following testimonial.

Phil did a tremendous professional stunning job on my floor. My kitchen floor was a bleak drab grey dull slate with heavily stained brown looking grout that was supposed to be cream! My floor had never been sealed in the 7 years since it had been laid. No matter how much I washed it- it always looked grim. I found out about The Tile Doctor and immediately searched for one in my area. He got back to me the next day and came to see my floor. I told him I don’t care if it’s perfect- I just want it ‘better’. Well today I can put my hand on my heart and say- it is perfect! I am thrilled. Better yet, my husband who did not think we needed a Tile Doctor at all, agrees that our floor is amazing! The grey slate is now is shiny and beautifully cleaned and coated – the grout is cream once again! The whole floor shimmers! I took photographs all the way through the process because the procedure was so thorough and the stages of the cleaning and sealing were fascinating to me. I am so happy now, that not only will I tell others about The Tile Doctor, but I have posted my impressive before and after photos on Facebook and people from all over the world are amazed and want to have their floors done by The Tile Doctor too! I wish you could see the photos- you would be impressed too! Thank you Phil, so much! Mrs Hayes
 
 

Cleaning Semi Riven Black Slate Floor Tiles

Slate Tile Flooring Cleaning In Northampton

Pictures below from rough slate tile flooring installed in the Kitchen and Toilet of a house in Northampton. The home owner had called us in to give the slate floor a clean and seal.

Kitchen Slate Floor Before Kitchen Slate Floor Before

Cleaning the Slate Tile Flooring

We cleaned the slate tiled floor with a strong dilution of Tile Doctor Pro-Clean in order to strip any remaining sealer together with a buffing machine fitted with a black scrubbing pad. The buffing machine doesn’t get into the grout lines so well so we had to use hand brushes for that. The floor was washed down with clean water and then left to dry overnight.

Sealing Slate Tiled Flooring

We came back the next day to seal the floor using five coats Tile Doctor Seal and Go which provides stain resistance as well as adding a low sheen to the floor.

Kitchen Slate Floor After Kitchen Slate Floor After

The home owner was very happy with work we did and left the comment below.

Effective and efficient service, would highly recommend Phil Vissian and the service provided.

Amanda, Northampton

Slate Tile Flooring Cleaning In Northampton

Quarry Tile Floor

Quarry Tile Floor in Weldon, Northants

I think you will be impressed with these photographs from a Quarry Tile floor we did in Weldon recently. This quarry tiles were installed in the kitchen and went through to the dinning room, hallway and down stairs cloakroom, at total of around 40sq metres

The tiles were recenctly installed and the customer called us in because they were unhappy with the finished result. This can be a common problem with Tilers who do a great job of levelling, tiling and grouting a floor but struggle on their knowledge of sealers. They were hoping for a high gloss finish but were left with a very dull and patchy floor.

Quarry Tile Floor Cleaning

We stripped the entire floor first using Tile Doctor Pro-Clean assisted by a rotary machine fitted with a black pad. This removed most of the sealer, however, we encountered more problems with grout haze which had been trapped underneath the sealer and had not been cleaned off properly to begin with. Also there were still patches of the original sealer which had been applied over a damp floor. The grout haze was removed by hand with wire bushes and more Pro-Clean and then the entire area was blanket stripped. This is an interesting technique unique to Tile Doctor which involves applying Remove and Go mixed with Nanotech Ultra-Clean to tiles and then covering in plastic sheeting and left for several hours to allow to soak into tiles. We then used a steam stripper and a wet vacuum to pick up to remove and rinse off the products. The area was then left to dry for 2 days assisted by dehumidifiers.

Quarry Tile Floor Sealing

After this time we returned to site to take damp metre readings and once we were happy that all areas were dry, we then applied 5 coats of Tile Doctor Seal and Go to protect floors and provide the high gloss finish that the customer requested.

Quarry Tiled Floor Restoration in Northamptonshire