Pitted Travertine Floor Tiles Filled and Polished in Rushden

Not only do we carry out the deep cleaning and restoration of all types of natural stone, we can also carry out repairs such as the filling of holes in stone, whether it be limestone, marble or as in this case Travertine. Travertine in particular is prone to a natural process of erosion know as pitting, this results in holes developing that easily fill up with dirt and muck over time and can be a real problem to maintain.

Pitted Travertine Before Filled Polished Rushden

This customer in Rushden called me in, as he felt the floor hadn’t been properly maintained since it had been installed twelve years prior and he was becoming concerned about the number of holes and pits that were appearing in the high traffic areas. The Travertine tiles had been laid in the hallway, kitchen and upstairs bathroom of the property but the problem was most apparent in the Kitchen.

Pitted Travertine Before Filled Polished Rushden

Burnishing and Cleaning a Travertine Tiled Floor

To get the floors clean and restore the polished appearance of the Travertine I decided to apply a set of Tile Doctor diamond encrusted burnishing pads. The process involves the application of four different pads applied in sequence from coarse to very fine, rinsing in-between each pad to remove dirt. As the floor had been installed in the Kitchen and the Hallway it made sense to split the work into two parts and work on each area separately.

The first pad is a coarse 400 grit pad that is attached to a rotary machine running at slow speed and with only water for lubrication. The pad is applied to the stone to removes minor scratches, sealers and dirt. It’s run over the entire floor and afterwards the floor is rinsed with water which is then extracted with the soil using a wet-vacuum.

I then repeated this same procedure with the second pad, which is a Medium 800 grit pad used to remove dirt from minor scratches and holes in the stone. After rinsing again, I went onto the third burnishing pad in the sequence which is a Fine 1500 grit pad that starts to rebuild the polish on the Travertine. I gave the floor another rinse and used the wet vacuum again to extract the water and soil from the floor. The last 3,000 grit super fine pad was then applied with a small amount of water sprayed onto the floor, this last pad really builds a nice shine on the stone.

Sealing a Travertine Tiled Floor

Once the burnishing process was completed the floor was left to dry off fully overnight and I came back the next day to continue with the work. I took a few moisture readings to confirm the floor was dry and then applied a single coat of Tile Doctor Colour Grow to seal the tiles. Colour Grow is a colour enhancing sealer that impregnates into the pores of the stone protecting it from within and improving the natural colours of the stone in the process. I particularly like to use it on Travertine as it really does bring out the brown shades in the stone.

Filling Holes in a Travertine Tiled Floor

Once the first coat of sealant had dried I started the work to fill the holes throughout the installation using appropriate colours of stone filler resin. I purposely delayed doing this until the first coat of sealer was in place in order to prevent excess resin from being absorbed into the tile and causing unwanted staining. There were quite a few holes to fill so it took a while to complete, the filler also needs several hours to dry and harden even when assisted with a fan. Excess filler is then polished off using a 17” rotary scrubbing machine fitted with a white polishing pad and any dust is carefully vacuumed up before applying a second coat of sealer. The floor was then allowed to dry before a final polish with a new 3000 grit pad to achieve a high sine finish.

Once the cleaning process was complete and the first coat of sealant had dried I then commenced the repair work by filling all holes throughout using appropriate colours of stone filler resin, the first coat of sealant is to stop the excess resin from being absorbed into the tile and causing staining, the filler is allowed to dry and harden for several hours assisted with a fan on site. Excess filler is then polished off using a 17” rotary scrubbing machine and a white buffing pad. Any dust is carefully vacuumed up before applying a second coat of sealant. This is then allowed to dry before a final polish with a new 3000 grit burnishing pad to achieve a deep sine finish.

Pitted Travertine After Filled Polished Rushden

I’m not sure the photographs really show off the transformation that I had managed to achieve, however my customer was certainly happy and left me the following glowing review via the Tile Doctor feedback system.

My hall and kitchen floor has been down for 12 years and has been a high traffic area. The Tile Doctor has literally made it look like new again. Holes filled, smooth, shiny and new again! My fully tiled bathroom has also been rejuvenated, wall tiles, shower tiles and floor tiles. The water now beads on the tiles like a freshly waxed car, and the walk-in shower has been perfectly resealed. Money very well spent.
Thank you so much! Mr.J. White, Rushden

Pitted Travertine After Filled Polished Rushden

It’s always nice to get feedback like that, it really does make your efforts feel appreciated.
 
 

Professional Travertine Tiled Floor Restoration in Northamptonshire

Ceramic Tile and Grout Deep Cleaned is a Rushden Sun Room

A customer from Rushden which is a large town in the east side of Northamptonshire, and my home town asked me to take a look at the Ceramic tile and grout in his Sun room. He has a large dog that sleeps on the sofa in this room and over the years the dog has walked in mud which has slowly degraded the grout lines and I suspect had probably never been sealed correctly or sealed at all.

The glazing on Ceramic tile is very resilient so we usually find it’s the grout discolouring that becomes most noticeable first due to the cementitious top layer which can trap dirt. In this case the Ceramic tiles had dulled over the years and as you might expect the white grout lines had become soiled and were almost black in places.

Ceramic Tile and Grout Before Cleaning Rushden Sun Room Cleaning Ceramic Tile and Grout Before Cleaning Rushden Sun Room

Deep Cleaning Ceramic Tile and Grout

To get the tile and grout clean the floor was first soaked in a strong dilution of Tile Doctor Pro-Clean and this was left to dwell for ten minutes. A rotary machine fitted with a black scrubbing pad was then used to scrub the cleaning solution into the tile and release the dirt. The pad can struggle to reach the recessed grout so to ensure this was also clean it was given a good scrub with a narrow stiff brush.

Cleaning Ceramic Tile and Grout During Cleaning Rushden Sun Room

We then used a spinning tool which forces hot water under high pressure onto the floor whilst simultaneously extracting the dirty water with a powerful vacuum. The objective of this action is to power wash the floor whilst rinsing and extracting the dirty cleaning solution at the same time.

Cleaning Ceramic Tile and Grout During Cleaning Rushden Sun Room

We inspected the grout lines and stubborn stains were treated with Tile Doctor Grout Clean-Up which was scrubbed in with hand brushes, this was then rinsed a second time until we were happy with the results. Grout Clean-Up is an acidic product that is particularly good at removing grout smears which can form a haze over a tile reducing its brilliance.

We then polished the floor with a white buffing pad and allowed the floor to dry overnight before returning the following day to apply Tile Doctor Ultra-Seal to all grout lines.

The furniture was too large and heavy for the customer to move out of the room, which was on a lower level than the rest of the ground floor. As a result, it was necessary to clean the floor in sections moving the furniture around the room on pads as needed.

Cleaning Ceramic Tile and Grout After Cleaning Rushden Sun Room

The Sun room floor look great afterwards, the grout especially looked clean and the sealer should ensure it stays that way for some time to come.
 
 

Deep Cleaning Ceramic Tile and Grout in Northamptonshire

Restoring a Riven Slate Patio Suffering from Grout Haze in Wollaston

This customer, who lives in Wollaston, a small village in Northamptonshire, called me to look at the unfortunate condition of her Riven Slate tiled patio. She had hired a builder to install it, but he had neglected to remove the grout haze which had occurred quickly enough, allowing it to set. He was subsequently unable to remove the haze because he had already sealed over it. This had left it looking very unsightly, as you can see in the photo below.

Newly Laid Riven Slate Patio Wollaston Before Cleaning

The customer initially contacted me back in December 2016. At that time, I did explain to the customer that the Winter wouldn’t be an ideal time to restore the patio, and that it would be best to carry out the work in the Spring. However, she was so unhappy with the appearance of the patio and – knowing she had guests coming over for Christmas – wanted something to be done to improve the condition of the tiles as soon as possible.

It was agreed that I would immediately carry out the removal of the old sealer and the grout haze beneath, but leave the re-sealing until the Spring of the following year when the weather was dry. The customer understood that when I returned in the Spring, the patio would require another light clean and brush to prepare it for sealing.

To put the customer’s mind at rest somewhat, I carried out a test clean on one slab of the patio using Tile Doctor impregnating, colour intensifying sealer, known as Colour Grow. This darkened the tile and provided a natural look finish, which was preferred by the customer. I also returned to the property several days later to carry out a water repellency test, but as you can see from the photo below, the rain beat me to it. Thankfully, the repellency test had positive results.

Newly Laid Riven Slate Patio Wollaston Testi Cleaning

I was then able to begin the cleaning process.

Cleaning and Sealing a Riven Slate Tiled Patio

To begin, I removed the old sealer using a strong mix of Tile Doctor Remove & Go, which is a stripper and cleaner. This product was scrubbed into the tiles with a rotary brush machine. Net, I rinsed away the resulting slurry and soaked up the water with a wet vax machine.

This initial clean exposed the true extent of the grout haze – it was over all every tile! My next course of action was therefore to remove this using Tile Doctor Acid Gel, which is a gel cleaner specially formulated to neutralise grout haze. This was allowed to dwell for a short period before I brushed it in.

Newly Laid Riven Slate Patio Wollaston During Cleaning

Following this, I gave the whole area a second brush with a small amount of water, before using a wet vax machine once again to make sure all cleaning chemicals were removed. I used the customer’s hosepipe to rinse down the entire patio as there was good drainage.

Newly Laid Riven Slate Patio Wollaston After 2nd Cleaning

I allowed the tiles to dry out naturally, before waited for a dry day in April this year to return to the property. During this day, I sealed the entire area with Tile Doctor Colour Grow sealer to really deepen the colour in the stone and provide the whole patio long-lasting protection against the elements.

Newly Laid Riven Slate Patio Wollaston After 1st Coat

The customer was exceptionally happy to have the patio restored to perfect condition. I’m sure she’ll make great use of it over the Summer!

Newly Laid Riven Slate Patio Wollaston Completed

 
 

Professional Riven Slate Tiled Patio Restoration in Northants

Stained and Damaged Sandstone Patio Restoration in Rushden

Lichen, moss and other plant-based staining is a common sight on patios exposed to the UK climate. For many property owners, it’s a very difficult task to keep patios looking great in the face of the natural effects of the environment. However always happy to help Tile Doctor is available to provide the professional cleaning and sealing needed on a regular basis.

This Sandstone tiled patio in Rushden was certainly a prime candidate for restoration. Not only was it completely covered in lichen and moss, but it was also cracked in parts and missing grout. The patio would therefore need not only cleaning and sealing, but also re-grouting.

Sandstone patio slabs before cleaning Rushden Sandstone patio slabs before cleaning Rushden

Cleaning a Stained and Damaged Sandstone Patio

To begin the restoration, I opted to power jet wash the entire area to remove as much of the initial layers of moss. Then, I mixed a strong dilution of Tile Doctor Pro Clean, which is a powerful and reliable alkaline cleaner suitable for use on both internal and external natural stone tiles. This was applied liberally to the patio and scrubbed into the stone to cut through the particularly stubborn stains. The two photos below show the fantastic result.

Sandstone patio slabs after cleaning Rushden Sandstone patio slabs after cleaning Rushden

Re-grouting and Sealing a Sandstone Patio

After completing the cleaning phase, I allowed the patio to dry completely overnight before returning to re-grout the entire area with mortar. To finish off I applied a fresh sealer in the form of Tile Doctor Seal and Go Extra, which an acrylic-based, fully breathable sealer appropriate for outside use.

The below pictures show the final result. As you can see, it was a complete transformation – and my very happy customer will agree! With the right products and methods, it’s possible to bring new life back to weathered patios.

Sandstone patio slabs after cleaning Rushden Sandstone patio slabs after cleaning Rushden

 
 

Professional Sandstone Patio Restoration Northamptonshire

Extremely Dirty and Damp Quarry Tiled Floor Restored in Higham Ferrers

This red Quarry tiled floor was in the dining room of a house in the East Northamptonshire market town of Higham Ferrers. Despite being an original feature of the property, the floor had never been taken care of and looked to be completely beyond salvation and what must be the worst condition I have seen in a long time.

Red Quarry Tiles Higham Ferrers Northants Before

When I first inspected the floor it became very quickly clear that it was suffering from severe damp problems, covering roughly two thirds of the entire surface area. I took damp meter readings and discovered that the floor was saturated as there was no damp proof course installed. This problem was compounded by staining from the glue residue used to hold down the linoleum which previously covered the tiles. But while some floors look beyond salvation, I was certain I could restore this one to an acceptable appearance.

A hallway in the property had the same Quarry tiles, but these had been painted with a red tile paint at some point in the past, which itself had worn off in the main traffic areas. These tiles had no damp problems and so it would just be a case of removing the rest of the paint and providing a thorough cleaning before sealing.

Red Quarry Tiles Higham Ferrers Northants Before

The customer was also keen that the dining room be restored as near as possible to the hallway tiles to try and achieve a uniform finish. I did inform the customer that due to the vast difference in condition this would be a challenge but I would do my best. A quote was given and work was booked in at the customer’s convenience.

Cleaning Extremely Dirty Quarry Tiles

Before beginning the restoration, I carried out a patch test to see which products would achieve the best results on the tiles. After vacuuming and mopping the floor to remove the immediate layers of muck, I decided my best course of action would be to use the heavy duty stripper, Tile Doctor Remove & Go.

Working in four separate sections, I applied the product then scrubbed it using a black stripping pad to a rotary machine. Remove & Go is designed to break down old sealers, paints and glues, making it an ideal product for use in this particular situation. This area was then rinsed off with a wet-vac machine and the process was repeated on the rest of the floor.

I then inspected the floor and noticed a few shiny patches where the old sealer hadn’t been fully removed, so I tackled these stubborn areas by hand with a second application of Remove & Go. A final rinse was given to the whole floor to make sure no excess cleaning products remained.

Sealing Quarry Tiles

After completing the cleaning process and removing as much water as possible using a wet vacuum, I installed a dehumidifier and left the tiles to dry for an entire month. Upon my return to the property I took damp meter readings to ensure the tiles were fully dry prior to the application of the sealer. This is crucial as excess moisture can cloud the sealer, rendering it less effective at protecting the stone.

I opted to use Tile Doctor Colour Grow to seal the floor primarily because is fully breathable and therefore ideal for floors that are prone to damp problems. It has the added bonus of being a colour intensifying sealer that really enhanced the natural reddish shades in the Quarry.

Red Quarry Tiles Higham Ferrers Northants After

As the pictures show, there was a vast improvement in the floor and the customer was pleased with the results. It really goes to show that while a floor might look beyond salvation, wait can in fact be restored to an acceptable condition using the right methods and products. The customer was also given advice on maintenance of this type of floor to keep it looking its best for years to come.

Red Quarry Tiles Higham Ferrers Northants After

 
 

Professional Quarry Tiled Floor Restoration in Northamptonshire

Restoring a Victorian Quarry Tiled Kitchen Floor in Rushden

A customer called me out to take a look at restoring the Red and Black Victorian Quarry tiles floor they had discovered under linoleum In the kitchen of their house in the town of Rushden.

I carried out a patch test to see which products would have the best results and although most of the old sealants had worn of over time there was still glue from the lino and patches of sealer that would have to be dealt with. A quote was given and accepted and the work was booked in to the customer’s convenience.

Black and Red Victorian Quarry Tiles Before Cleaning Rushden

Cleaning Victorian Quarry Tiles

After vacuuming and mopping the floor I decided my best course of action would be to spray Tile Doctor Remove and Go to 25% of the area, this was then scrubbed in by machine using a black stripping pad. This area was then rinsed off with an extraction machine and the process repeated over the rest of the floor. I then inspected the floor and noticed a few shiny patches where the sealant hadn’t been fully removed so I then tackled these stubborn areas by hand with a second application of Remove & Go. A final rinse to the whole floor was given to make sure no trace of cleaning product remained before sealing.

As much water as possible was removed using the extraction machine and a dehumidifier installed and left for seven days to assist the drying process.

Sealing Victorian Quarry Tiles

On my return I confirmed the floor had dried thoroughly by taking took damp meter readings in different parts of the floor. All was well and so I proceeded to seal the tiles using multiple coats of Tile Doctor Seal and Go which matched the customers’ requirements of gloss finish.

Black and Red Victorian Quarry Tiles After Cleaning Rushden

As the pictures show there was a vast improvement in the floor and the customer was very pleased with the results. They were also given information on maintenance of this type of floor to keep it looking its best for years to come.
 
 

Victorian Quarry Tile hidden under Lino Restored in Northamptonshire

Cleaning and Repointing a Patio in Rushden

You may be surprised but we just clean interior stone and tile we also specialise in exterior stone cleaning as well as you will see with the post below where we cleaned and re-pointed a neglected patio at a house in Rushden.

The first photo shows the condition of the patio which hadn’t been professionally cleaned for over forty years, weeds and moss had eaten through all the original mortar and made any remaining cement very lose and would need to be replaced after pressure washing.

Patio Before Cleaning and Repointing in Rushden

The second picture shows the equipment set up ready to pressure wash the patio, the power of the pressure washer blasted away most of the dirt and we used Tile Doctor Remove and Go on any stubborn stains that became evident.

Patio Before Cleaning and Repointing in Rushden

The third picture below shows the results after the patio has been pressure washed; you can see that the remaining mortar had all but washed away.

Patio Cleaned not Repointing in Rushden

After allowing a few days for the patio to completely dry out I returned to site to repoint all joints between the slabs. There are a few different colours to choose from and on this occasion the customer chose a light grey. The final picture shows the finished patio after it had been sealed.

Patio Cleaned and Repointed in Rushden

The customer was over the moon with the results as she had no idea that the slabs were different colours under the 40 years of dirt, grime and weeds.
 
 

Patio Cleaning in Northamptonshire

Grout Cleaning Difficulty in a Rushden Kitchen

This customer from Rushden called me in because she was having difficulty keeping the grout in her kitchen clean although the ceramic tiles themselves were fairly easy to maintain.

On speaking to the customer it became evident that the one coat of sealant that was originally applied to the grout five years ago had all but worn off and the cleaning products she was using were too strong reducing the life of the sealer and now dirty water getting into the now porous grout which was causing staining each time she mopped the floor.

Cleaning Grout Ceramic Tiles in Rushden Before

I gave the customer a quote for deep cleaning and extraction of tiles and grout lines, as they were thinking of selling the house they didn’t want to have the expense of re-colouring the grout. We decided the best course of action would be re-sealing the grout with Tile Doctor Grout Seal & Go after cleaning and this should protect it going forward.

Deep Cleaning Ceramic Tile and Grout

To get the grout clean and lift out the dirt we used Tile Doctor Pro-Clean mopped onto the floor and scrubbed into the grout lines with a stiff grout brush. The second and third pictures below show the equipment we use to deep clean and scrub the grout and to extract the water under pressure to clean the grout as best as possible.

Cleaning Grout Ceramic Tiles in Rushden During Cleaning Grout Ceramic Tiles in Rushden During

Sealing Grout

The final pictures below show the overall end result after allowing the floor to drying overnight and then sealing the grout with two coats of Tile Doctor Grout Seal & Go.

Cleaning Grout Ceramic Tiles in Rushden After Cleaning Grout Ceramic Tiles in Rushden After

I also talked the customer through Tile Doctor recommended cleaning procedures and advised her that she was entitled to a free bottle of Tile Doctor Neutral Cleaner which would keep the floor looking at its best for much longer and would not affect the grout sealant.
 
 

Cleaning Ceramic Tile and Grout and Sealing in Northamptonshire

Kitchen Quarry Tile Cleaning and Sealing in Rushden

This job was to strip and re-seal these Quarry tiles installed in a commercial kitchen which was undergoing refurbishment at a canteen in Rushden, Northamptonshire. The tile finish had dulled and there was a lot of staining to the grout.

Quarry Tiles in Rushden before cleaning

Cleaning Quarry Tiles

As there was little in the way of kitchen units to protect I go straight down to stripping down the floor using a strong dilution of Tile Doctor Pro-Clean which is a multi-purpose cleaner/stripper that’s safe to use on stone, tile and grout. The solution was applied with a mop and left it to dwell on the floor for twenty minutes in order to give it chance to soak into the tile surface and get to work on the existing sealer and dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad and stiff hand brushes were used along the grout lines to get the grout clean. The resulting soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and stubborn areas re-treated. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.

Sealing Quarry Tiles

After checking the tiles had dried I proceeded to seal the floor using four coats of Tile Doctor Seal and Go which will protect the floor from staining going forward and also adds a nice shine to the tile.

Quarry Tiles in Rushden After cleaning

 
 

Commercial Kitchen Quarry Tile cleaning in Northamptonshire

Polished Marble Floor Covered in Grout Haze in Irthlingborough

These photos are from a newly installed Polished Marble floor in the kitchen at a residence in Irthlingborough Northants which had been left covered in grout haze. The customer called the builder back as they were unhappy with the finish but he could not rectify the problem, so the customer contacted Tile Doctor to see if anything could be done.

This is a problem we often come up against where a builder or tiler does a good job of laying the tiles but for some reason doesn’t remove all the grout from the tile and we have even seen some jobs where the grout smears have been sealed over which makes it even more noticeable especially on a polished floor. Fortunately for the customer we are able to resolve such problems and after agreeing the process we set about solving the problem.

Marble Tiled Floor In Irthlingborough before cleaning

Burnishing Polished Marble Tiles

To protect the kitchen units from any splashing etc. all the kick boards were removed and plastic sheeting fitted to protect new doors and panels before any work was undertaken.

Polished Marble is a very hard surface that has to be burnished with diamond encrusted pads to restore the finish so we set about this task using a set of Tile Doctor Burnishing Pads. The pads come in a set of four, you start with the coarse pad together with a little water and this cut’s through and removes surface grime, surface seal and in this case grout haze as well. You then progress through the other finer pads one by one until you get to the final polishing pad which provides a high polish. The pads did the trick and had the surface polished to a high shine which was the look the customer was hoping they would have had in the first place.

The floor was looking great but I was concerned about the grout, most people don’t realise but the top layer of grout is actually slightly porous and will attract dirt and discolour over time, this is especially the case in a bathroom or kitchen. After discussing this with the customer we sealed the grout with Tile Doctor Ultra-Seal which provides a natural look whilst preventing contaminates reaching the grout.

All in the job took two days and the customer was extremely happy with the final result.

Marble Tiled Floor In Irthlingborough after cleaning

 
 

Cleaning and Polishing Marble Tiled floor in Northamptonshire